RDTA - is based on the Rebuildable Dripper Atomizer, with the taste of the drip atomizer and the convenience of the oil atomizer. The RDTA structure is quickly accepted by a large number of players. Drip + Tank is a perfect interpretation of the 1+1=2 theory. This cotton tutorial is written for newcomers and is based on content and entry level.
There is a RTDA fromvapeciga which is calledSteam Crave Aromamizer Plus RDTA. It would definitely make a deep impression on you with precise-controlled taste, vapor and lasting endurance. 2 pieces of 10ml glass tube guarantee a constant vaping experience no matter what it comes down to the amount of the liquid or vaping device. The well-equipped airflow system is located on the bottom, capturing an intense or fluffy taste by exposing one or more air holes, greatly enhancing the immersion when the dense vapor comes across the finest flavor. 5 colors vary from your preference.
Specifications:
Brand: Steam Crave
Model: Aromamizer Plus
Material: Stainless steel + glass
Capacity: 10ml
Diameter: 30mm
Thread: 510
Product Size: 3 x 3 x 6.3cm
Package Size: 8.3 x 8.3 x 4cm
Product Weight: 0.094kg
Package Weight: 0.18kg
Package Contents:
1 x Aromamizer Plus RDTA 10ml, 1 x 10ml Spare Glass Tank, 1 x Allen Key, 1 x Vape Band, 1 x 510 Drip Tip Adapter, 1 x Accessory Bag, 1 x English User Manual
The general RDTA structure is of the upper and lower type, the upper part is the atomization chamber and the lower part is the oil storage bin. The drooping cotton extends into the bottom oil storage bin to carry the oil from bottom to top. Unlike the usual negative pressure oil guiding system, the RDTA’s oil guiding route is the opposite route. Therefore, in the RDTA cotton processing, there are many newcomers often have problems: the oil guiding speed can not keep up, the oil guiding is not Completely and so on…
Here’s how to dismantle how to improve the oil guiding performance of RDTA through some tips for handling cotton.
- Prepare a workbench (of course, you can use a host instead), scissors, pointed tweezers, and a piece of cotton.
- Cut the appropriate cotton (of course, you can tear it by hand and see if you are used to it). As for the amount of cotton, you need to understand the basics. The basic explanation is not repeated here. The general comparison suggests a little more than the normal amount of cotton.
- After cutting, please remove the hard cotton skin on both sides to leave the fluffy cotton in the middle.
4, the cotton strips into a more “round strip”, but do not use brute force to compress the cotton, to maintain fluffy. Finish the excess cotton wool and make a pointed head.
These steps are all based on the general nebulizer for cotton, but it is recommended that the amount of cotton be a little bit more, the cotton must be fluffy! ! !
- Passing the cotton through the center of the heating coil, the thread of the Notch Coil is relatively soft, so it can be carried out by rotating the sliver while wearing it (refer to the moving line of the arrow), as is the case with some relatively small diameter heating coils. It is possible to avoid the situation in which the coil is deformed when wearing cotton.
2, after wearing, pull the cotton back and forth, cut off the part of the tight cotton head.
3, the cutting position of the scissors will appear “pressed” situation, first manually sort the end that has just been cut.
4.Pull back and forth simply so that the lengths of the two sides are the same.
- First press the cotton gently with your finger to see the length of the cotton to be reserved. Generally speaking, it is almost the bottom of the middle, which is almost the same! The cotton is too short, and it is necessary to tilt the atomizer to the end of the oil. Cotton is too long, and the volume of cotton will take up the capacity of the oil tank. After all, the oil tank of RDTA is generally not very large. The length can be taken as needed.
2, the side is simply sorted and broken up. - The end that has not been broken is lightly fixed by hand. Note! It is light! Too heavy a hand will compress the cotton. Then use the tweezers to gently remove some excess cotton wool from the broken end. This step is the focus, which can remove some messy cotton wool and make the cotton texture more “fluid”. Secondly, it is possible to reduce the “volume” of cotton cotton feet, which is beneficial to increase the oil storage capacity of the oil storage tank. Finally, such cotton feet are soaked in the smoke oil, which will naturally spread the contact “net” of cotton and smoke oil. Remember the roots in the picture at the beginning of the article?
4, the other side of the same operation, and finally sorted out the shape, the density of the two sides of the cotton is significantly smaller. The amount of cotton before the “slightly more” is also removed because of the broken cotton feet, the amount of cotton at this time is just good.
- Cut off the excess cotton feet.
- Put the cotton in to look at the length. If there is a problem, continue to trim.
- Put down the glass bin and you will find that the cotton on both sides of the coil collapses.
- Use a pair of tweezers to tidy up so that the cotton on both sides of the coil is filled with coils. It is OK to have a slight arch.
Such cotton will have a certain oil-conducting effect in the structure of the RDTA, and the area of the contact with the smoke oil after the cotton feet are scattered will be larger. Of course, the treatment of the theorem is relatively simple.