Lighting Information (PAR, PPFD, umol/s, DIL)

Measuring Light: The important differences between PPF and PPFD
There exists some industry inconsistencies between how PPF and PPFD is used when describing their lamps
output. For those basing their decision on which lamp is best suited their garden it’s important to know what
these different terms mean.
PPFD (Photosynthetic Photon Flux Density) μMol/M2S is certainly well defined, accepted and
consistently used. However, PPF is used inconsistently by nearly every source referencing it. We
have seen a quantum sensor manufacturer indicate that the terms PAR, PPF, and PPFD are all the
same having units of μMol/M2S. We have also seen many refer to PPF in various ways having units of
μMol/M2S. We have seen industry leading light manufacturers refer to PPF as the total radiant light
output in the PAR region of a lamp in units of μMol/S. So the question is: If PPFD is well defined and
uniformly accepted, why then are so many within the industry using PPF to have the same meaning?
The likely answer is that there is no good solid standard for the industry to work within. So taking a look at area
lighting and their value definitions the best conclusion we can draw is that the units for PPF should be
μMol/S. We think the reason for this confusion results from a disconnection between the lamp and sensor
manufacturers, particularly since lamp specifications should be based on PPF and field measurements
based on PPFD. Another issue contributing to the confusion is that so many manufacturers, both lighting and
measurement, do not consistently show the complete proper engineering units in their marketing, operating,
and specification documents.
PPF as μMol/S is the value that a grow lamp should specify for its total light output (Radiant Watts would also
be appropriate), this would be similar to using Lumens for a regular area light. PPFD is the primary
measurement taken by a Quantum PAR meter and is expressed as a density over a unit of area, this would be
similar to using Lux or Foot-Candles on a regular light meter. We do believe these to be the proper definitions
as originally intended, but have been unable to find any industry standard or document to substantiate that.
For your consideration:
PPF (Photosynthetic Photon Flux) issued by (or should be) manufactures as the lamps total emitted number of
photons per second in the PAR region. Units of measure: μMol/S
PPFD (Photosynthetic Photon Flux Density) represents a field measurement and is defined as, the number of
photons in the PAR region emitted per M2 per Second. Units of measure: μMol/M2S
In standard commercial/industrial lighting terminology the use of the term “flux” generally applies to the light
energy on a per time basis which in grow lamps would be the lamps PPF value. By definition, Energy per time
or energy transfer rate is defined as Power. In lighting terms, light power is generally defined in terms of
Radiant Flux or Luminous Flux.
The point of this discussion is that the term “flux” used in the absence of density applies to energy or power
emitted, but not over a specific area. The term “Density” generally applies to the energy or power per a
volume of space, in the case of lighting, it generally applies to an area rather than a volume, since light striking
a surface area is more applicable than light within a volume.
Lamp manufacturers should rate the lamps overall output in PPF (μMol/S) or PAR radiant Watts rather than
Lumens which are strictly for human vision. Ideally in the future we may have a generally accepted PAR
sensitivity standard that can be applied to give results as Yield PPF or Yield Radiant Watts which would be a
more equivalent measurement to Lumens, but would be plant specific
If a lighting manufacturer, not a lamp manufacturer, were to use PPFD as a specification for a particular
fixture/lamp combination they would need to include all of the following information for the user to properly
interpret the information being given:

  1. Provide the height from which the measurement was taken.
  2. Provide multiple locations across the illuminated footprint at meaningful points allowing for
    interpretation of consistency of intensity and footprint limitations.
  3. Provide multiple sets of PPFD measurements at different heights.
    To publish in a PPFD value various considerations with this approach would be:
  4. Measurements must be taken with reflectors in place to achieve accurate results.
  5. For HID lamps since the lamps are sold separate from the reflectors there can be many different
    combinations of lamps and reflectors. Any measurements taken need to be specific to a particular
    lamp/reflector combination.
  6. At the close height that grow lamps are used their light distribution patterns will not change in a regular
    expected manner. The use of a reflector in the design requires that a certain minimum measurement
    distance is used for values to stabilize and act with an expected regularity for varying heights. This
    height in many cases will be greater than the typical height used for an indoor grow, but would likely be
    good for a greenhouse supplemental application. Basically we are referring to relationship of Light
    Intensity as a function of 1/d2, where d is the measurement distance from the light source. Until this
    certain height is achieved, you will not see measured values following this rule at all.
  7. As for LED panels, these measurements will not stabilize until a height is reached for which the beam
    patterns of the LEDS have interlaced enough to be somewhat homogenous, both with respect to
    intensity and mixture of different LED wavelengths.
  8. Interpreting the results of overlapping light from adjacent lamps in multiple lamp systems can be a
    difficult task, but would be necessary to determine the true quantity of light intensity at any particular
    point.
  9. It will likely still take some field experimentation with proper measurement equipment and different
    configurations of the lamps to come to the optimal lamp placement, particularly in a multiple lamp
    system.
    This is all great information but how do I use it in the field?
    As indoor gardeners we are trying to optimize all the conditions in the garden which include an even spread of
    light at enough intensities to meet our crops daily light needs. It’s important to have accurate canopy values as
    it relates to the amount of CO2 that is necessary to meet crop flowering demands. So while this may seem like
    a lesson in advanced mathematics, it’s really good for the gardener to approach how much light they expect to
    see at the canopy based on this approach:
  10. Take the PPF value that the manufacturer provides for total PPF output.
  11. Reduce that output by ~20% as a reasonable loss associated with light not making it to the canopy.
  12. When you have that number divide it by the canopy surface area in M^2 and that would represent what
    intensity you would expect over that surface area.
  13. Use that value to calculate how much CO2 your plants would require based on RH between 50-70%.

This is an example of how you would use the PPF to get an expected PPFD value;
Lamp PPF Output: 1,100 μMol/S
Grow Area: 4’ x 4’ = 16 sq-ft = 1.49 M2
Grow Losses off Canopy: 20% = 80% used
Light Actually Used = 1,100 x .8 = 880 μMole/s
Sample Average PPFD Formula: 880 μMole/S ÷ 1.499 M2 = 591 μMole/M2 -S
Summary Conclusions: PPF and PPFD certainly have their place when discussing grow lamp output values
and how those values may then be measured in the field. However, there does exist inconsistencies on how
lamp and sensor manufacturers use these terms and for the average gardener who may lack advanced
degrees in Physics and Engineering, these are not going to be terms they can easily come to grips anyway.
As such we felt introducing an alternative method, which was easier to comprehend, would be in order.

5 Likes