Are you sure it’s gnats?
They look like tiny gnats. It was like 7 years ago since I last saw a gnats but I thought I remember them being bigger
Do they fly around like they’re really f’n stupid and slow??
They fly fairly quickly. Like they are idiots though
The big cola phentotype looks to be a full week or two behind the others. I hate the way the others are growing though with their calyxes all separated.
What is this yellowing from? Looks like Zn or Mg. Possibly due to a Ca deficiency? I noticed some spots forming while the yellowing was happening.
I’ve reduced nutrients to 0.6EC and still using Calcium Nitrate just at a reduced rate. I really feel like the added potassium and sulfates are adding a positive to the smell.
I know this isn’t good but outside my house reaks of dankness. I only have 4 of my allotted 12 plants so I’m not worried about it.
7 Likes
I chopped the three that we’re foxtailing bad 4 days ago.
One of the buds that fell off at harvest is dry enough to smoke. Good taste. Nice burn. No flush just reduced nutrients a lot and tapered down on the Calcium nitrate and increased the potassium sulfate. Was at 0.6EC for the week before chopping.
4 Likes
The rosin press does not give a fuck if foxtailed or not.
4 Likes
True that.
This is the only one that remains. One branch is down accidentally, so will be a good comparison once these go down in 2 weeks I give them
7 Likes
wow those got phat under that cmh.
Damn right they did. I wish I marked the clones I took. Ended up chucking them since the other phenotype wasn’t worth keeping and im nearly positive I didn’t clone the one pictured since it was the runt.
If the smoke is decent I’ll have to buy another pack and find that again. That’s a 2gpw pheno right there.
2 Likes
Had to chop earlier than intended. Lost like 2oz to botrytis. Last time I grew this strain had the same issue though my dehumidifier hose kinked that time. This time everything was perfect. Still will pull 8+oz. Not bad for a 2x2 wwwaaayyyy overgrown scrog on a 315w cmh
A good deal of trichomes are milky so not a total loss.
Exhausted, time for bed.
3 Likes
If I do indeed get 8oz off what’s left I’ll be at 1.15gpw
Pulled a bit over 2#
This is off the 3 that foxtailing
Not a special bud just found it outside of the jar this morning
4 Likes
Going to order more seeds of that strain and see how close I can get it to 2gpw with better training(not putting screen on when they are already 4ft) and co2
Very happy with the smoke. Fruity danky cheesy smelling. I’ve never seen such white ashes and it burns nice.
After a 2 week cure it will only get better.
It dried a little quicker than I wanted, but oh well.
Oh and I didn’t flush. OMG!
7 Likes
Looks like it gets the job done 
2 Likes
nice looking rosin you got there!
what temp, how much pressure and how long did you press?
1 Like
I usually do 110C 10 tons over a 3x3.
I did an experiment this time 17 bags. With 4 different press types over 4 different temperatures. 90C, 95C, 100C and 110C. Press types were quick to 10 ton for 3min, 1ton to 4 to 7 to 10 over 2min, 1 ton for 10 seconds to warm up then quick to 10 ton for 3min total and the last type was just a low pressure press at around 2 ton for 3min.
The best temps I saw for this strain and those tests were 110C. Produced a lot of clear presses and was pushing 15% on the first press. The lower temperatures where I gradual increase in pressure produced more buttery results. But the results weren’t that consistent.
6 Likes
How/what do you use to do the heating?
1 Like
There’s a couple PID controllers. The plates have three holes in both the top and the bottom. The hole in the middle has a thermometer and the other two have heat probes
1 Like