I would also suggest that anyone with a dedicated rosin press should go through this process on a small scale at least once - It may take some time however if you are analytical about it and make some conclusions its worth it.
If you find that you have no extractable trichomes left in your chip bags you might also find high volume of waxes and fats that liquefy at around the same temperatures are likely contaminating and reducing the concentration of your concentrate.
Happy Squishing!!
Yes one could likely however if I was to abandon my current outlook I think I would go with @ReikoX ’ s process; simple and minimal waste. -I also think the whole neighobrhood would start to narrow in on your space if you were heating your greenhouse or house with those puppies 
Already smells like a dead skunk in front of a burning tire factory…,Joy’s of living on the ole dirt road in a legal state of mind…
Sitting here watching plants grow on a rain day. Hoping the Ups guy will drop of my press and plates, just got bags and pre press
this is the press I’m looking at getting, says 20ton for 300 with free shipping, almost seems too good no? the only review is someone giving 1* because they had to pay import duties of 78$ idk I might go for it what do you think??
https://www.aliexpress.com/item/4000692178818.html?spm=a2g0o.productlist.0.0.7ce31036ztMw5R&algo_pvid=6402fa0c-35fd-4cbe-99ba-1fae4cbead1f&algo_expid=6402fa0c-35fd-4cbe-99ba-1fae4cbead1f-2&btsid=0be3743b15888385547966175efd3e&ws_ab_test=searchweb0_0,searchweb201602_,searchweb201603_
Getting my Dake 10 ton press and 4x7 plates today. Just wanted to make sure it came in before posting this. Cost of press allowed me to update to better plates and controllers. I have a friend at Livernois Machine Tools that turned me on to it.
And the plates I ordered.
https://www.ebay.com/itm/4x7-Rosin-Heat-Plates-Kit-DIY-20-30-Ton-Solventless-Extraction-set-600W-110V/153920937395?pageci=1390b5a8-45ed-4a7b-af62-9eb40509dcd8
Just wanted to put it out there it’s a 200 savings compared to the HF one.
I built my press (I’ll post some pictures once I get a chance) and have been pressing and enjoying my labors.
I only have an old school titanium nail and butane torch.
I need an enail or something like an enail.
I use a Magneto pen, they have coil less igniter and cupped nail head. Igniters are about 5 us each pen was 40. Also like it has hidden silicon rosin storage in screw off end cap
Nectar Collector or Honey Straw, those are where its at. I have a couple titanium nails and recently got a couple nice quartz bangers with the balls and whatnot but I just keep comin back to my nectar collector. Its easier and it hits better.
I need to find a better way to smoke my hash though. Can’t do knives since I have an induction top stove, and I’m not really a fan of smokin out of a bowl, especially when its soaked in rosin it doesn’t actually light and I’m not sure vaping it is getting everything 
Cardboard square, pin and glass…old school
What’s your guys method for getting rosin off the tool into a jar?
What I do is scrape the rosin on the edge of the open jar so the rosin ends up on the inner wall of the jar. Then I put the jar between my plates at 170 degrees for a few minutes.
The rosin then melts down off the sides of the jar and pools in the middle.
So far this is the best method I’ve found, but please share yours.
I scrape the tool onto the parchment, then form a ball by folding it on itself. I can then pull the ball off the parchment with my tool and plop it in the container. Puttin the parchment on an ice pack helps if you have a runny consistancy.
Hahahaha, what he said! Did that for the first time in ages at an old mates BBQ the other day. Well we actually used a cigarette bridge at the top of the glass but pretty much the same thing.
I pull it off the tool with a small silicon dab mat.
Been experimenting with “chottle tech”.
I like it so far… Haven’t perfected it yet though… This is 14g in and 2g out… not my best presses yet but I was doing lower pressure and temp.
Here is a great vid on “chottle”:
15% seems pretty good, seems like an interesting technique
Thanks for sharing this @MumenRyder! Squish videos are always fun although I don’t think too many folks are posting the hundreds of tests it takes to dial in a recipe for a specific strain as many of us know, just the glory!
Chottle Tech is a great way to reuse bags cut for the bottle tech method. If you have a 2" round pre-press, you can run 3 x 5g pucks per 2x4" bag (1 BT, 2 CT) and is certainly a budget-friendly and efficient method with the right input.
I would likely only turn on the camera on for known strains from familiar producers I already have recipes for, like many of these guys “OMG shes a gusher guys!” 
I will take 15% of goodness over 30% of what’s left after most people press it IMO, quality over yields every time, keep refining your method and yields can come and go
go for it my friend 1 day you can teach me best way how to press rosin…
Ooooh thats a good idea!
Is there some kind of quickstart guide to this? its all so overwhelming with guys discussing in detail all these plates and stuff, so for somebody who has never done this before. I would like to just jump into, and I wonder if I am thinking wrong here.
Am I forgetting something on my shopping list?
1rosin press,
2a bunch of these micron bags to put the weed in
3parchment paper
put the stuff in the bags, press it in the thing while it sits on the parchment paper right?
sorry i know this sounds dumb, but id like some to know if I am going in the right direction or not.
That pretty much sums it up, you will likely want some kind of dab tool to remove the rosin from the parchment and some sort of container to store the rosin in. Not to mention a torch and rig to consume the product.
